Dowco-power-sports Guardian Scooter Cover Manuel d'utilisateur télécharger pdf

Installation

Read instructions before using.

Unfold cover and remove Warranty Card. Locate

the “FRONT” tag.

Position the front of the cover on the scooter.

Starting in the front wheel area, pull down over the

windshield and “tuck” the elastic hem under the

centerline of the wheel.

Working rearward, slide the cover down the sides,

avoiding “snag” points. The cover should be long

enough to allow the elastic hem to fully wrap below

the centerline of the rear wheel and have a tight fit

along the perimeter. Care should also be taken to

avoid placing the dark gray material against hot

engine components as melting or burning may

occur.

Caution: Mirrors, muffler ends, shifters, brakes and

foot pegs are common wear points. Do not allow

fabric to “snag” around them.

Important

The aluminized heat-resistant coating is designed

to protect the cover from melting or burning when in

contact with hot engine parts, pipes and mufflers.

Waiting approximately five-ten minutes for cool-

down before placing the cover on the motorcycle

will greatly increase the life of your cover.

Note: The aluminized coated fabric is similar to

high quality ironing board cover materials. The

coating may experience some minor “flaking”

during normal use and this will not affect the

performance of the cover.

Grommet patches are provided to enable you to

securely lock the cover under the motorcycle. A

cable lock or chain is recommended. However,

should you be unable to unlock the cover, it may

have to be cut through the hem and grommet area

to be removed.

Care and Cleaning

Your cover requires very little maintenance. Normal

dirt and grime should be brushed off with a soft terry

cloth or removed with warm water and a mild

detergent using a sponge or terry cloth. The cover

should be thoroughly dried before using.

Caution: Do not place in washing machine and do

not wring or twist the cover to remove moisture.

A water-repellant spray material, such as 3M

Scotchguard

, is recommended for increased water

resistance.

Although protected with UV inhibitors, the fabric

may fade in direct sunlight after continuous use.

This is normal wear.

Important

Failure to comply with the above directions may

reduce the life of your cover. If you have any

questions or comments, please contact either your

dealer or DOWCO Inc.

Congratulations on your purchase of a Guardian

scooter cover. Properly cared for, your cover will last for

many years of service. Our scooter covers are manufactured from a medium-weight polyester coated

fabric which has excellent water and weather resistance and may be used either inside or outside. An

aluminized heat-resistant coating is applied to the inside bottom portion so that the cover may be applied

over warm engine pipes. Your cover also contains an elastic shock cord that is sewn into a continuous

hem. This feature eliminates the need for tie-downs. The integral vent allows harmful moisture to escape.

The following information should be used to ensure maximum longevity.

Note: All Guardian

covers are sized to fit specific scooters. It is very important that you have the

correct one for your application.

This cover is not designed for covering your scooter while it is trailered, in the back of a

pick-up truck or strapped to back of a motor home.

INSTRUCTIONS FOR THE INSTALLATION OF

A GUARDIAN

SCOOTER COVER

Item: 14002-00

Revised 04/04

Printed in China

4230 Clipper Drive Manitowoc, WI 54220 U.S.A.

Phone: (800) 558-7755 - Fax: (920) 682-5891 - Email: [email protected]

Visit our Web Site! - www.dowco-inc.com

In severely windy conditions, “ballooning” of the cover may occur, which may result in the wind causing

the scooter to tip over. It is strongly recommended that your scooter be sheltered whenever high winds

are expected. If sheltering is not an option, facing into or rearward of strong gusts may reduce the poten-

tial for wind damage. Attaching a bungee cord or cable through grommet areas may also help prevent

“ballooning” in high winds.

Résumé du contenu

Page 1 - Printed in China

InstallationRead instructions before using.Unfold cover and remove Warranty Card. Locatethe “FRONT” tag.Position the front of the cover on the scoote

Commentaires sur ces manuels

Pas de commentaire

Dowco-power-sports Guardian Scooter Cover Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sports et loisirs Dowco-power-sports Guardian Scooter Cover. Dowco Power Sports Guardian Scooter Cover User Manual [it] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Sports et loisirs Dowco-power-sports Guardian Scooter Cover