Dowco-power-sports Guardian WeatherAll Motorcycle Cover Manuel d'utilisateur télécharger pdf

Installation

Read instructions before using.

Unfold cover and remove Warranty Card from vent

area. Locate ”FRONT” tag, indicating which part of

the cover goes to the front of the motorcycle.

Position the front of the cover on motorcycle with

the vent positioned approximately over the seating

area. Starting in the front wheel area, pull down

over the windshield and “tuck” the elastic hem

under the centerline of the wheel.

Working toward the rear of the motorcycle, slide the

cover down the sides, avoiding “snag” points. The

cover should be long enough to allow the elastic

hem to fully wrap below the centerline of the rear

wheel and have a tight fit along the perimeter. Care

should also be taken to avoid placing the dark gray

material against hot engine components as melting

or burning may occur.

Caution: Mirrors, muffler ends, shifters, brakes and

foot pegs are common wear points. Do not allow

fabric to “snag” around them. Antennas are capable

of puncturing the cover – use extreme care.

Important

The aluminized heat-resistant coating is designed

to protect the cover from melting or burning when in

contact with hot engine parts, pipes and mufflers.

Waiting approximately five-ten minutes for cool-

down before placing the cover on the motorcycle

will greatly increase the life of your cover.

Note: The aluminized coated fabric is similar to

high quality ironing board cover materials. The

coating may experience some minor “flaking”

during normal use and this will not affect the

performance of the cover.

Grommet patches are provided to enable you to

securely lock the cover under the motorcycle. A

cable lock or chain is recommended. However,

should you be unable to unlock the cover, it may

have to be cut through the hem and grommet area

to be removed.

Care and Cleaning

Your cover requires very little maintenance. Normal

dirt and grime should be brushed off with a soft terry

cloth or removed with warm water and a mild

detergent using a sponge or terry cloth. The cover

should be thoroughly dried before using.

Caution: Do not place in washing machine and do

not wring or twist the cover to remove moisture.

A water-repellant spray material, such as 3M

Scotchguard

, is recommended for increased water

resistance.

Although protected with UV inhibitors, the fabric

may fade in direct sunlight after continuous use.

This is normal wear.

Important

Failure to comply with the above directions may

reduce the life of your cover. If you have any

questions or comments, please contact either your

dealer or DOWCO Inc.

Congratulations on your purchase of a GUARDIAN

WEATHERALL

™

motorcycle cover. Properly cared for,

your cover will last for many years of service. GUARDIAN

WEATHERALL

™

is manufactured from a medi-

um-weight polyester coated fabric which has excellent water and weather resistance and may be used

either inside or outside. An aluminized heat-resistant coating is applied to the inside bottom portion so that

the cover may be applied over warm engine pipes. Your cover also contains an elastic shock cord that is

sewn into a continuous hem. This feature eliminates the need for tie-downs. The integral vent allows harm-

ful moisture to escape. The following information should be used to ensure maximum longevity.

Note: All GUARDIAN

WEATHERALL

™

covers are sized to fit specific motorcycles. It is very important that

you have the correct one for your application.

This cover is not designed for covering your motorcycle while it is trailered or in the back of a

pick-up truck.

INSTRUCTIONS FOR THE INSTALLATION OF

GUARDIAN

WEATHERALL

™

MOTORCYCLE COVER

FORM # 141129-00

Revised 06/04

Printed in China

In severely windy conditions, “ballooning” of the cover may occur, which may result in the wind causing

the motorcycle to tip over. It is strongly recommended that your motorcycle be sheltered whenever high

winds are expected. If sheltering is not an option, facing into or rearward of strong gusts may reduce the

potential for wind damage. Attaching a bungee cord or cable through grommet areas may also help pre-

vent “ballooning” in high winds.

4230 Clipper Drive Manitowoc, WI 54220 U.S.A.

Phone: (800) 558-7755 - Fax: (920) 682-5891

Visit our Web Site! - www.dowco-inc.com

Résumé du contenu

Page 1 - Printed in China

InstallationRead instructions before using.Unfold cover and remove Warranty Card from ventarea. Locate ”FRONT” tag, indicating which part ofthe cover

Commentaires sur ces manuels

Pas de commentaire

Dowco-power-sports Guardian WeatherAll Motorcycle Cover Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sports et loisirs Dowco-power-sports Guardian WeatherAll Motorcycle Cover. Dowco Power Sports Guardian WeatherAll Motorcycle Cover User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Sports et loisirs Dowco-power-sports Guardian WeatherAll Motorcycle Cover